Is It Safe to Burn Leftover Pine Wood from My Book Case?
I recently built a bookcase using quality pine boards from Menards and now I have some leftover scraps. While having a bonfire and cooking hot dogs, I thought…
safety
Why did my glass shower door explode and how can I prevent it in the future?
I recently experienced a terrifying situation where my glass shower door exploded randomly. It was about four years old and likely installed when my house was built. After…
Is It Safe to Cut Open an Acetylene Tank?
I recently picked up an old acetylene tank from someone on a marketplace. I'm planning to use it for a pass-through forge in my metalworking setup. I already…
How to Dispose of Water-Based Polyurethane Rags Safely?
Hey everyone! I'm a bit of a fire safety nut when it comes to oil-based polyurethane rags, so I treat those with a lot of caution. I usually…
Is It Safe to Use a Dremel by Hand for Carving Antler and Bone?
I'm not a woodworker, but I've been told this is the place to ask my question. I'm interested in using a Dremel to carve and drill into materials…
Help! My Electrician Left Wiring in a Mess—What Are My Options?
I recently bought a single-story house without an attic, sitting on a slab. After tearing out a really ugly drop ceiling, I found a mess of wires hanging…
Are Barrina Grow Lights Safe to Use?
I've been using Barrina grow lights for about a year now, and they've worked great for me. I always thought that LED lights were generally safe since they…
Is it safe to daisy chain power strips for lighting in my living room?
I'm dealing with a tricky lighting situation in my apartment. I have three light bulbs in the kitchen, three on a fan in the dining room, and one…
What to Do After Accidentally Destroying a Wasp Nest While Tree Cutting?
I accidentally took out a wasp nest while I was cutting down a tree and now I'm stuck hiding inside my house. How long will it be before…
What's the Best Way to Nail Boards That Are Out of Reach?
I'm trying to nail down some cedar shake siding, but the nails are about two feet out of reach. The scaffolding I have set up isn't tall enough…
Is My Husband in Danger After Spraying the Fence Without a Mask?
My husband just finished spraying our wooden fence with a sealer, but he didn't wear a mask while doing it. Should I be worried about his health?
Is Using a 1/2 Inch Router in a Router Table a Mistake?
I recently built a router table attached to my tablesaw using a 1/2 inch router that I inherited. I've noticed that a lot of DIYers on YouTube tend…
Is Using a Drawknife Really Dangerous?
Hey everyone! I'm currently restoring a drawknife and I'm getting ready to make a shavehorse to go along with it. However, I've got this nagging fear about using…
Should I Wear Gloves While Using Chisels and Gouges for Woodcarving?
I'm just starting out in woodcarving and I've heard conflicting advice about wearing gloves. Are gloves mainly for when you're using a knife, or should I also consider…
Table Saws for Newbies: Are They Worth It?
I'm just starting out in woodworking and finally have a garage to work in! I've been trying to get the hang of things with just a circular saw,…
Thoughts on Thin-Rip Table Saw Jigs?
Hey everyone! I'm trying to avoid making super thin cuts against the fence on my table saw. I've been looking into thin-rip table saw jigs, like the ones…
Should the Offcut Side of the Blade Matter When Cutting?
I've got a half sheet of plywood (48x48) and I need to cut it into strips that are 8 3/4 inches wide. I've heard conflicting advice about whether…
Do Forstner Bits Really Need to be Used at Low RPMs?
I recently noticed that my Forstner bits have a specified maximum RPM rating, with the largest one (7/8") suggesting a max of 450 RPM. My drill press doesn't…
Is It Safe to Mount a 55" TV on a Single Stud?
I'm thinking about mounting my 55" TV in the center of my mantle, but I'm a bit concerned. Can single stud TV mounts hold the weight reliably, or…
When Can I Bring My Polyurethane-Finished Furniture Inside?
I recently refinished some dressers and applied the last coat of polyurethane today (Friday). I'm wondering how long I should wait before bringing them inside since they're currently…